ASROCK K8 COMBO-Z Ficha de datos

1MOTHERBOARDK8 Combo-ZUser ManualVersion 1.0Published July 2004Copyright©2004 ASRock INC. All rights reserved.

101.4 ASRock 8CH I/O1 Parallel Port 8 Microphone (Pink)2 RJ-45 Port 9 USB 2.0 Ports (USB01)3 Side Speaker (Gray) 10 USB 2.0 Ports (USB23)4

112. InstallationK8 Combo-Z is an ATX form factor (12.0-in x 9.6-in, 30.5 cm x 24.4 cm) motherboard.Before you install the motherboard, study the conf

122.1 CPU SocketsThis motherboard is equipped with two types of CPU sockets. You may choose toinstall either 939-Pin CPU (AMD Athlon 64FX) or 754-Pin

132.2 CPU InstallationStep 1. Unlock the socket by lifting the lever up to a 90o angle.Step 2. Position the CPU directly above the socket such that th

142.4 Installation of Memory Modules (DIMM)This motherboard is equipped with five 184-pin DDR (Double Data Rate) DIMM slots.I.For 939-Pin CPU users, p

15notchbreaknotchbreakInstalling a DIMMPlease make sure to disconnect power supply before adding orremoving DIMMs or the system components.Step 1. Unl

162.5 Expansion Slots (PCI and AGP Slots)There are 3 PCI slots, and 1 AGP slot on K8 Combo-Z motherboard.PCI Slots: PCI slots are used to install expa

17JR1 JL12.6 Jumpers SetupThe illustration shows how jumpers aresetup. When the jumper cap is placed onpins, the jumper is “Short”. If no jumper capis

18FLOPPY1Pin12.7 Onboard Headers and ConnectorsOnboard headers and connectors are NOT jumpers. Do NOT placejumper caps over these headers and connecto

19DUMMYGND+5VIRTXIRRX1GNDGND+5VABACKOUT-RBACKOUT-LAUD-OUT-LAUD-OUT-RMIC-POWERMIC1USB_PWRUSB_PWRP+6P-6P+7P-7GNDGNDDUMMY1connect to the SATA HDDpower

2Copyright Notice:No part of this manual may be reproduced, transcribed, transmitted, or translated inany language, in any form or by any means, excep

20GNDPWRBTN#PLED-PLED+DUMMYRESET#GNDHDLED+HDLED-1+5VDUMMYDUMMYSPEAKER1MIDI_OUTJAB2JBYJBB2MIDI_IN+5VJAYGNDGND1JAXJAB1+5VJBXJBB1+5VSystem Panel Header T

212.8 Serial ATA (SATA) Hard Disks InstallationThis motherboard supports Serial ATA (SATA) hard disks and RAID functions. Thissection will guide you t

223. BIOS SETUP UTILITY3.1 IntroductionThis section explains how to use the BIOS SETUP UTILITY to configure your system.The Flash Memory on the mothe

233.1.2 Navigation KeysPlease check the following table for the function description of each navigationkey.Navigation Key(s) Function Description

24BIOS SETUP UTILITYMainH/W Monitor Boot Security ExitAdvanced SettingsWARNING : Setting wrong values in below sectionsmay cause system to malfunction

25Cool ‘n’ QuietUse this item to enable or disable AMD’s Cool ‘n’ QuietTM technology.Processor Maximum MultiplierIt will display Processor Maximum Mul

26Processor MultiplierThis item will show when “Multiplier/Voltage Change” is set to [Manual];otherwise, it will be hidden. You may set the value from

273.3.2 Chipset ConfigurationOnBoard AC97 AudioSelect [Auto] or [Disabled] for the onboard AC97 Audio feature.OnBoard LANThis allows you to enable or

28BIOS SETUP UTILITYACPI SettingsSelect auto-detect ordisable the STRfeature.Select ScreenSelect Item+- Change OptionF1 General HelpF9 Load DefaultsF1

29BIOS SETUP UTILITYPrimary IDE MasterSelect the typeof device connectedto the system.Select ScreenSelect Item+- Change OptionF1 General HelpF9 Load D

3Contents1. Introduction ... 51.1 Package Contents ...

30TYPEUse this item to configure the type of the IDE device that you specify.Configuration options: [Not Installed], [Auto], [CD/DVD], and [ARMD].[Not

31BIOS SETUP UTILITYFloppy ConfigurationSelect the type offloppy driveconnected to thesystem.Select ScreenSelect Item+- Change OptionF1 General HelpF9

32BIOS SETUP UTILITYConfigure Super IO ChipsetAllow BIOS to Enableor Disable FloppyController.Select ScreenSelect Item+- Change OptionF1 General HelpF

33BIOS SETUP UTILITYUSB ConfigurationTo enable or disablethe onboard USBcontrollers.Select ScreenSelect Item+- Change OptionF1 General HelpF9 Load Def

34BIOS SETUP UTILITYHardware Health Event MonitoringSelect ScreenSelect ItemF1 General HelpF9 Load DefaultsF10 Save and ExitESC Exitv02.54 (C) Copyrig

35BIOS SETUP UTILITYBoot Device PrioritySpecifies the bootsequence from theavailable devices.A device enclosed inparenthesis has beendisabled in theco

363.6 Security ScreenIn this section, you may set or change the supervisor/user password for the system.For the user password, you may also clear it.B

37BIOS SETUP UTILITYMain Advanced H/W Monitro Boot SecurityExit system setupafter saving thechanges.F10 key can be usedfor this operation.Select Scree

384. Software Support4.1 Install Operating SystemThis motherboard supports various Microsoft® Windows® operating systems:98 SE / ME / 2000 / XP. Becau

39APPENDIX:AMD’s Cool ‘n’ QuietTM TechnologyFor power-saving sake, it is strongly recommended to enable AMD’s Cool ‘n’ QuietTMtechnology under Window

44. Software Support ... 384.1 Install Operating System...

51. IntroductionThank you for purchasing ASRock K8 Combo-Z motherboard, a reliable motherboardproduced under ASRock’s consistently stringent quality c

61.2 SpecificationsPlatform: ATX Form Factor: 12.0-in x 9.6-in, 30.5 cm x 24.4 cmCPU: 1. 939-Pin Socket Supporting AMD AthlonTM 64FX Processor2. 754-P

7USB 2.0: 8 USB 2.0 Ports:4 Ready-to-Use USB 2.0 Ports on the I/O PanelPlus 2 On-Board Headers Supporting 4 Extra USB 2.0 Ports(see CAUTION 7)ASRock

8CAUTION!1. This motherboard is equipped with two types of CPU sockets. You maychoose to install either AMD 939-Pin CPU or AMD 754-Pin CPU into thismo

91.3 Motherboard Layout1 PS2_USB_PWR1 Jumper 17 System Panel Header (PANEL1)2 ATX Power Connector (ATXPWR1) 18 Chassis Speaker Header (SPEAK