ASROCK B75M-ITX Manual de usuario

1B75M-ITXUser ManualVersion 1.0Published March 2012Copyright©2012 ASRock INC. All rights reserved.

107. The maximum shared memory size is de ned by the chipset vendor and is subject to change. Please check Intel® website for the latest informa-tio

11 pend to RAM (S3), hibernation mode (S4) or power off (S5). With APP Charger driver installed, you can easily enjoy the marvelous charging experien

1220. ASRock Internet Flash searches for available UEFI firmware updates from our servers. In other words, the system can auto-detect the latest UEFI

131.3 Motherboard Layout 1 SPI Flash Memory (64Mb) 2 SATA2 Connector (SATA_1, Black) 3 SATA3 Connector (SATA_0, Gray) 4 SATA2 Connector (S

141.4 I/O Panel* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED indications.

15 To enable Multi-Streaming function, you need to connect a front panel audio cable to the front panel audio header. After restarting your comput

16Chapter 2: InstallationThis is a Mini-ITX form factor (6.7" x 6.7", 17.0 x 17.0 cm) motherboard. Before you install the motherboard, study

172.3 CPU Installation For the installation of Intel 1155-Pin CPU, please follow the steps below.Before you insert the 1155-Pin CPU into the socket,

18Pin1alignment key alignment key Pin11155-Pin CPUStep 3. Insert the 1155-Pin CPU:Step 3-1. Hold the CPU by the edge which is marked with a black

192.4 Installation of CPU Fan and Heatsink This motherboard is equipped with 1155-Pin socket that supports Intel 1155-Pin CPUs. Please adopt the type

2Copyright Notice:No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, exce

202.5 Installation of Memory Modules (DIMM)This motherboard provides two 240-pin DDR3 (Double Data Rate 3) DIMM slots, and supports Dual Channel Memo

212.6 Expansion Slot (PCI Express Slot)There is 1 PCI Express slot on this motherboard.PCIE slots: PCIE1 (PCIE 3.0 x16 slot) is used for PCI Express

222. If you have already installed the onboard VGA driver from our support CD to your system, you can freely enjoy the bene ts of dual monitor fu

23Surround Display FeatureThis motherboard supports surround display upgrade. With the internal VGA output support (DVI-D, D-Sub and HDMI) and externa

24 For Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS: Right click the desktop, choose “Personalize”, and select the “Display Settings” tab

25 * ASRock Smart Remote is only supported by some of ASRock's motherboards. Please refer to ASRock's website for the motherboard support

262.9 Jumpers SetupThe illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap is pl

272.10 Onboard Headers and ConnectorsOnboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Plac

28USB 3.0 Header Besides two default USB 3.0 (19-pin USB3_3_4) ports on the I/O panel, there is (see p.13, No. 12) one USB 3.0 header on this mo

29System Panel Header This header accommodates (9-pin PANEL1) several system front panel (see p.13, No. 8) functions. Connect the power switch, re

3Contents1 Introduction ... 71.1 Package Contents ...

30 Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin CPU fan still can work successfully even without the

312.11 Serial ATA (SATA) / Serial ATA2 (SATA2) / Serial ATA3 (SATA3) Hard Disks InstallationThis motherboard adopts Intel® B75 chipset th

32 Caution1. Without SATA 15-pin power connector interface, the SATA / SATA2 / SATA3 Hot Plug cannot be processed.2. Even some SATA / SATA2 / SAT

33 How to Hot Plug a SATA / SATA2 / SATA3 HDD:Points of attention, before you process the Hot Plug:Please do follow below instruction sequence to proc

342.14 Driver Installation GuideTo install the drivers to your system, please insert the support CD to your optical drive rst. Then, the drivers co

352.15.2 Installing Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit Without RAID FunctionsIf you want to install Windows® 7 / 7 64-bi

36Chapter 3: UEFI SETUP UTILITY3.1 IntroductionThis section explains how to use the UEFI SETUP UTILITY to con gure your system. The UEFI chip on the

373.1.2 Navigation KeysPlease check the following table for the function description of each navigation key. Navigation Key(s) Function Description

383.3 OC Tweaker ScreenIn the OC Tweaker screen, you can set up overclocking features.CPU Confi gurationCPU Turbo Ratio Use this item to change the r

39Primary Plane Current Limit Use this item to con gure the maximum instantaneous current allowed for the primary plane. The default value is [Auto]

43 UEFI SETUP UTILITY ... 363.1 Introduction ...

40DRAM tRASUse this item to change RAS# Active Time (tRAS) Auto/Manual setting. The default is [Auto].Command Rate (CR) Use this item to change Comman

41Voltage Confi gurationPower Saving ModeUse this to enable or disable Power Saving Mode. The default value is [Disabled].CPU Voltage Use this to sele

42Setting wrong values in this section may cause the system to malfunction.3.4 Advanced ScreenIn this section, you may set the con gurations for th

433.4.1 CPU ConfigurationIntel Hyper Threading Technology To enable this feature, a computer system with an Intel processor that sup-ports Hyper-Thr

44 to the IA-32 Intel Architecture. An IA-32 processor with “No Execute (NX) Memory Protection” can prevent data pages from being used by malicious s

453.4.2 North Bridge Configuration Primary Graphics Adapter This allows you to select [Onboard] or [PCI Express] as the boot graphic adapter priority

463.4.3 South Bridge ConfigurationOnboard HD AudioSelect [Auto], [Enabled] or [Disabled] for the onboard HD Audio feature. If you select [Auto], the

473.4.4 Storage ConfigurationSATA Controller(s) Use this item to enable or disable the SATA Controller feature.SATA Mode Selection Use this to sele

483.4.5 Intel(R) Rapid Start TechnologyIntel(R) Rapid Start Technology Use this item to enable or disable Intel(R) Rapid Start Technology. Intel(R)

493.4.6 Intel(R) Smart Connect TechnologyIntel(R) Smart Connect Technology Use this item to enable or disable Intel(R) Smart Connect Technology. Int

5Chapter 1: IntroductionThank you for purchasing ASRock B75M-ITX motherboard, a reliable motherboard produced under ASRock’s consistently stringent q

503.4.7 ACPI ConfigurationSuspend to RAMUse this item to select whether to auto-detect or disable the Suspend-to-RAM feature. Selecting [Auto] will e

51OMG (Online Management Guard)Administrators are able to establish an internet curfew or restrict internet access at speci ed times via OMG. You may

523.5 Hardware Health Event Monitoring ScreenIn this section, it allows you to monitor the status of the hardware on your system, including the param

533.6 Boot ScreenIn this section, it will display the available devices on your system for you to con g-ure the boot settings and the boot priority.

543.7 Security ScreenIn this section, you may set or change the supervisor/user password for the system. For the user password, you may also clear it

553.8 Exit ScreenSave Changes and ExitWhen you select this option, the following message “Save con guration changes and exit setup?” will pop-out. S

56Chapter 4: Software Support 4.1 Install Operating System This motherboard supports various Microsoft® Windows® operating systems: 7 / 7 64-bit / Vi

57Installing OS on a HDD Larger Than 2TB in AHCI ModeThis motherboard adopts UEFI BIOS that allows Windows® OS to be installed on a large size HDD (&g

61.2 Specifications Platform - Mini-ITX Form Factor: 6.7-in x 6.7-in, 17.0 cm x 17.0 cm - All Solid Capacitor design (100% Japan-made high-quality

7 - Supports DVI with max. resolution up to 1920x1200 @ 60Hz - Supports D-Sub with max. resolution up to 2048x1536 @ 75Hz - Supports Auto Lip S

8 Connector - 3 x SATA2 3.0 Gb/s connectors, support NCQ, AHCI and Hot Plug functions - 1 x SATA3 6.0Gb/s connector - 1 x CIR header - CPU/Chas

9 WARNING Please realize that there is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Over