ASROCK AD2700-ITX Manual de usuario

1AD2700-ITX / AD2500-ITXUser ManualVersion 1.0Published November 2011Copyright©2011 ASRock INC. All rights reserved.

108. ASRock XFast USB can boost USB storage device performance. The performance may depend on the properties of the device.9. ASRock XFast LAN provi

111.3 Motherboard Layout (AD2700-ITX) 1 Print Port Header (LPT1, White) 12 Consumer Infrared Module Header (CIR1) 2 COM Port Header

121.4 Motherboard Layout (AD2500-ITX) 1 Print Port Header (LPT1, White) 12 Consumer Infrared Module Header (CIR1) 2 COM Port Header

131.5 I/O Panel (AD2700-ITX)** If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”. See the table below

141.6 I/O Panel (AD2500-ITX)** If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”. See the table below

15Chapter 2: Installation This is a Mini-ITX form factor (6.7" x 6.7", 17.0 x 17.0 cm) motherboard. Before you install the motherboard, stud

162.3 Installation of Memory Modules (SO-DIMM)AD2700-ITX / AD2500-ITX motherboard provides two 204-pin DDR3 (Double Data Rate 3) SO-DIMM slots.1. It i

172.4 Expansion Slot (PCI Slot)There is 1 PCI slot on this motherboard. PCI slot: The PCI slot is used to install expansion card that has the 32-

182. If you have installed onboard VGA driver from our support CD to your system already, you can freely enjoy the benefi ts of dual monitor

19 HDCP Function HDCP function is supported on this motherboard. To use HDCP function with this motherboard, you need to adopt the monitor

2Copyright Notice:No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, exce

20* ASRock Smart Remote is only supported by some of ASRock motherboards. Please refer to ASRock website for the motherboard support list: http://ww

212.7 Jumpers Setup The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap is pl

222.8 Onboard Headers and ConnectorsOnboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placin

23System Panel Header This header accommodates(9-pin PANEL1) several system front panel (see p.11 or 12 No. 11) functions. Connect the power swi

24Chassis Speaker Header Please connect the chassis (4-pin SPEAKER 1) speaker to this header.(see p.11 or 12 No. 14) PLED (System Power LED

25Serial port Header This COM1 header supports a(9-pin COM1) serial port module. (see p.11 or 12 No. 2)Print Port Header This is an interface

262.9 Serial ATA (SATA) / Serial ATAII (SATAII) Hard Disks Installation This motherboard adopts Intel® NM10 Express chipset that supports Serial ATA (

27 Caution1. Without SATA 15-pin power connector interface, the SATA / SATAII Hot Plug cannot be processed.2. Even some SATA / SATAII HDDs provide

28 How to Hot Plug a SATA / SATAII HDD:Points of attention, before you process the Hot Plug:Please do follow below instruction sequence to process the

292.12 Driver Installation GuideTo install the drivers to your system, please insert the support CD to your optical drive fi rst. Then, the drivers co

3Contents1 Introduction ... 51.1 Package Contents ...

30Chapter 3: UEFI SETUP UTILITY3.1 IntroductionThis section explains how to use the UEFI SETUP UTILITY to confi gure your system. The UEFI chip on the

313.1.2 Navigation Keys Please check the following table for the function description of each navigation key. Navigation Key(s) Function Description

32 AD2500-ITX

33Setting wrong values in this section may cause the system to malfunction.3.3 Advanced ScreenIn this section, you may set the confi gurations for the

343.3.1 CPU ConfigurationIntel Hyper Threading Technology To enable this feature, it requires a computer system with an Intel processor that suppor

353.3.2 Chipset ConfigurationACPI HPET Table Use this item to enable or disable ACPI HPET Table. The default value is [Enabled]. Please set this opti

363.3.3 Storage ConfigurationSATA2 Mode Use this to select SATA2 mode. Confi guration options: [IDE Mode], [AHCI Mode] and [Disabled]. The default val

373.3.4 Super IO ConfigurationCOM1 Port Use this item to enable or disable the onboard serial port. COM1 Port Address Use this item to set the a

383.3.5 ACPI ConfigurationSuspend to RAMUse this item to select whether to auto-detect or disable the Suspend-to-RAM feature. Select [Auto] will enab

393.3.6 USB ConfigurationUSB 2.0 ControllerUse this item to enable or disable the use of USB 2.0 controller. USB 3.0 ControllerUse this item to enabl

43.5 Boot Screen ... 423.6 Security Screen ...

403.3.7 Voltage ConfigurationDRAM VoltageUse this to select DRAM Voltage. The default value is [Auto]. +1.05V VoltageUse this to select +1.05V Voltag

413.4 Hardware Health Event Monitoring ScreenIn this section, it allows you to monitor the status of the hardware on your system, including the param

42Setup Prompt TimeoutThis shows the number of seconds to wait for setup activation key. 65535(0XFFFF) means indefi nite waiting.Bootup Num-LockIf this

433.6 Security ScreenIn this section, you may set or change the supervisor/user password for the system. For the user password, you may also clear it.

443.7 Exit ScreenSave Changes and ExitWhen you select this option, it will pop-out the following message, “Save confi guration changes and exit setup?”

45Chapter 4: Software Support 4.1 Install Operating System This motherboard supports various Microsoft® Windows® operating systems: 7 32-bit. Because

5Chapter 1: IntroductionThank you for purchasing ASRock AD2700-ITX / AD2500-ITX motherboard, a reli-able motherboard produced under ASRock’s consiste

61.2 Specifications Platform - Mini-ITX Form Factor: 6.7-in x 6.7-in, 17.0 cm x 17.0 cm - All Solid Capacitor design (AD2700-ITX) - Solid Capacitor

7 LAN (AD2500-ITX) - Realtek PCIE x1 LAN RTL8105E - Speed: 10/100 Ethernet - Supports Wake-On-LAN - Supports PXE Rear Panel I/O I/O Panel (AD2700

8 WARNING Please realize that there is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Over

9CAUTION!1. About the setting of “Hyper Threading Technology”, please check page 34.2. Due to the chipset limitation, the actual memory size may be